Please note, your bicycle has been supplied in a carton (box) in a semi-knock-down state. This means it requires some basic assembly & a thorough inspection by a competent experienced person prior to riding.
-------------------------------------------------------------------------------------------
If you live outside of the UK you may be liable to local taxes, ie import duty and the relevant charges levied by the courier, which may include an admin fee. Please contact your local customs department for clarification. We cannot be held liable for any additional charges you may have to pay when the product is in your country.
If an order is rejected at customs due to non payment of local taxes/import taxes and the item is returned, a return charge will be deducted from your refund.
-------------------------------------------------------------------------------------------
We strongly recommend that this inspection is carried out by a trained bicycle technician at a bicycle shop where they regularly build and service bicycles. It’s paramount for the riders safety that this bicycle is thoroughly checked over for any potential safety issues prior to riding. We will not accept any liability whatsoever for injury or death sustained as a result of improper assembly and inspection of your new bicycle. If you should encounters any such issue during assembly / inspection please do not hesitate in contacting us using the appropriate warranty or returns form to be found at http://www.stomp-group.com/
-------------------------------------------------------------------------------------------
Ride safe
Wherever you ride, you should take every precaution to protect yourself from potential injury. Always wear a protective helmet and gloves and make sure you stay visible to others by wearing brightly coloured clothing such as a reflective jacket. If you are riding in a skate park or other off-road location, ensure you are always well protected. If performing tricks or riding difficult obstacles such as ramps, curbs, rails or trails we strongly advise the use of a full face helmet, protective gloves, elbow & knee pads, shin/ankle pads & protective shoes.
-------------------------------------------------------------------------------------------
Servicing (1 week service)
For your safety and also to validate your warranty, your new bike needs to be serviced after approximately 1 weeks riding or 50 miles (whichever comes sooner). This is because all moving parts are liable to bed-in and require adjustment e.g. crank bearings, wheel bearings & headset bearings. The chain may also require re-tensioning. All nuts & bolts should also be checked to ensure they are sufficiently tight along with wheel spokes (especially on BMX bikes which tend to be ridden much harder than other bikes).
-------------------------------------------------------------------------------------------
Usage
All mafiabikes BMX’s are designed for use at an entry level. This means small airs, jumps or hops (max 1 foot or 12 inches),which may incorporate basic tricks such as up to 360° spins). Foot jams, foot jam whips, bar spins or manuals. If you push your BMX beyond this level, you do so entirely at your own risk. Should you wish to go beyond these limits we advise you upgrade your bicycle to one that is built entirely of aftermarket parts.
-------------------------------------------------------------------------------------------
Servicing (continued)
For your safety and for the optimum performance of you bicycle it should be checked thoroughly by a trained bicycle technician on a regular basis. This is especially true for BMX bikes, which may sustain regular immeasurable impacts. A bicycle which has not been serviced correctly and is ridden in a manner which it may sustain regular immeasurable and unquantifiable impacts, may cause component failure and potential injury or death. Stomp Racing LTD will not be held liable in any way for any injury or death sustained as a result of improper/incorrect use, servicing or maintenance. As a guide we suggest a full inspection by a qualified person every 3 months however this is only a guide & is by no means exhaustible. It is your responsibility to ensure your bicycle is safe to ride at ALL TIMES. If you ride your bicycle in an ‘extreme way’ i.e. to perform tricks, you should inspect your bicycle EVERY time you ride it and also during the period you are riding it. It is highly recommended that you carry any essential tools you may require for continued maintenance whilst you are riding. This is a perfectly normal and accepted practise whilst riding BMX. E.g. an impact from a jump or air may cause your bars to move, also your cranks or your spokes could work loose. You should be prepared at all times to be in a position to rectify any servicing or maintenance issue which could potentially cause component failure, injury or death. Your safety is entirely your responsibility.
-------------------------------------------------------------------------------------------
Headset adjustment
Loosen the 2 rear pinch bolts at the back of the handlebar stem tighten the top bolt (centre of the stem top cap). Not too hard, the bolt simply pre loads the bearings. You should be able to still turn the bars easily and smoothly. If they feel notchy then loosen the bolt slightly. If there is movement back & forth in line with the frame, then tighten the bolt. Once satisfied, re-tighten the pinch bolts on the stem nice & tight to prevent the stem slipping on the fork steer tube
-------------------------------------------------------------------------------------------
Handlebar adjustment
Your bars should normally be installed inline with your forks (looking from the side). However if you are a little small for the bike you may want them back towards you a touch. There is very little reason to angle your bars forward; this will simply affect the bikes geometry & thus performance making riding difficult. Make sure you install the faceplate for the stem evenly, with an equal gap to the top & bottom of the stem to faceplate. Make sure the bolts have a little grease on them as this will allow you to tighten them more than without grease. Tighten the bolts diagonally top to bottom, and then switch to opposing side. This will ensure even pressure on the bars. If your bars persist to slip, try roughing up the knurled section of the bar & also scratch grooves into the stem faceplate & body. This will help the two parts grip each other better.
-------------------------------------------------------------------------------------------
Brake Pad Adjustment
Your brake(s) should be set by the factory, however as it beds in it may require adjustment. To adjust your brake pad, first loosen the allen bolt attaching it to the calliper enough that the shoe will move freely. Next pull your brake lever so the pad makes firm flat contact with the wheel rim. Whilst holding the brake lever, adjust & position the pad so that it sits flat on the rim. Make sure the pad is away from the tyre. A rubbing pad on the tyre will cause the tyre sidewall to fail & the tube to blow out BANG. This can cause injury. Once you are fully satisfied with the position of the pad, tighten the pad retaining bolt/nut whilst FIRMLY pulling the brake lever and preventing the pad from spinning (sometimes this requires 3 hands). This will give a nice flat pad adjustment & very effective breaking performance. However, it may also cause the brake to squeal, especially if rim protecting soft pads are being used (clear pads). To prevent brake squeal, attempt to angle the leading edge of the pad slightly into the rim. The rear of the pad should be approx 1-2 mm off the rim when the leading edge 1st touches the rim. Braking performance will still be good & hopefully the SQUEAL is reduced or totally eliminated. Note: if your brakes are not installed but supplied as a kit, please see the separate brake assembly instructions and online ‘how to’ install brake video.
-------------------------------------------------------------------------------------------
U or V-brake adjustment
The U or V-brake utilises 2 separate levers to apply pressure to the wheel rims. Each lever has a spring which is adjustable in tension. In order for both levers to pull together & for the pads to make contact at the same time, the springs need to be adjusted for balanced movement. If one arm is moving more than the other, you must reduce it’s spring tension (usually a small allen key bolt in the side of the brake/pad lever) Depending on the brake this can be either clockwise, or anticlockwise, therefore you will need to experiment. You are trying to achieve the brake levers to be in roughly the same position at rest & pull together at the same time when you pull the brake. A perfect set-up will see both pads hit the rim at the same time.
-------------------------------------------------------------------------------------------
U-brake cable adjustment
Once your brake is set up correctly you may want to finally adjust the brake lever pull for your personal preference. There are normally 2 adjusters, 1 on the lever & 1 on the cable termination on the frame. Screw the cable adjuster anticlockwise to reduce cable pull i.e. in order that the pads hit the rim sooner for a give brake lever operation. If you have run out of adjustment it may be necessary to adjust the cable length at the cross-over junction or on the cross over cable itself. Simply loosen the cable connection & pull a small amount of cable through. Note: screw your cable adjusters clockwise until they are approx 1/3 from the hard stop before you carry this out. This will allow you to fine adjust your cable pull afterwards.
-------------------------------------------------------------------------------------------
Brake lever position
You can angle your brake lever however you like, however the best angle is normally tending down pointing to the ground. This allows the lever to be out of the way whilst performing bar spins etc. To adjust, simply loosen the lever on bar and slide/angle to your desired position. Note: if you do not fully tighten, it is less likely that the lever will be damaged whilst bailing a trick or jump as it will simply spin out of the way under the impact force. If fully tight, the lever may fail as a result of a given impact.
-------------------------------------------------------------------------------------------
3-piece pinch bolt crank arm adjustment
Your cranks may come loose from time to time, if they do, this is how to tighten them: Loosen the 2 pinch bolts (where fitted e.g mafia clip), next tighten the centre crank arm bolt (in line with crank axle) then re-tighten the pinch bolts. If you cranks are still after tightening, it may be that the bearings are not fully pressed in. To ensure they are pressed in firmly, remove the crank arms fully & using a suitably sized large socket matching the outer race of the bearing unit, drift the bearing hard into place in the BB housing (using a hammer). Do this both sides & then re-assemble the crank arms.
-------------------------------------------------------------------------------------------
Hubs & bearings
Most of our models use loose ball hubs unless specified otherwise e.g. bb-kush, kush, clip & Manhattan silver all use loose ball hubs. As the bearings bed in, it may be necessary to tighten the cone nuts from time to time. If there is wobble (side to side) your bearings could probably do with a slight tweak. Remove the wheel, loosen the cone locking nuts & carefully tighten the cone nuts. The wheel should spin freely, but there should be no side-to-side play. Once you are satisfied, re-tighten the locking nuts & replace the wheel. Note this can also be a good time to check there is plenty of grease in your bearings. If they are looking/feeling a bit dry, stuff in some fresh grease before adjusting the cone nut.
-------------------------------------------------------------------------------------------
Tyre Pressure
tyre pressure is a personal preference. Some people like their tyres soft, others like them rock hard. Your tyres are only designed for pressures up to 60 psi, so always use a pressure gauge & never over do the pressure. If you desire higher pressure we suggest you invest in some hi pressure aftermarket tyres.
-------------------------------------------------------------------------------------------
Chain Adjustment
Your chain should be tight at all times. The reason for this is that a tight chain will make it easier for you to keep your pedals in the desired position whilst performing tricks where you feet leave the pedals e.g. foot-jam-whip. To tighten your chain, 1st loosen your rear wheel nuts enough that the wheel only just moves in the rear drop outs (moves with a little force). Pull the rear wheel hard back keeping it inline in the frame. Next pull the non-drive side back a tiny bit more that the now tight chain side & tighten the non-drive side wheel nut. The wheel will now be slightly out of line in the frame. Next grab the tyre somewhere close to the seat tube & pull the wheel hard over towards the drive side until the wheel is centralised. Once you have it centralised tighten the drive side wheel nut. This procedure can be a little tricky & will take a few attempts to get the hang of, but the result is a very tight chain & pedals that stay put whilst performing tricks. When you rotate the pedals you may notice a very tight spot, or a very loose spot. This is often caused by the chain wheel (front sprocket) not being centralised. In order to centralise it, try loosening the sprocket bolt (to the rear) a small amount & then spinning the crank arms. The chain wheel should centralise (note you should not fully loosen, only a little). Once centralised tighten the sprocket bolt. Note: if this is all too complicated & you are not interested in tight crank arms for tricks, simply align your rear wheel centrally pulling back on the wheel till the chain is tight, then tighten the wheel nuts.
-------------------------------------------------------------------------------------------
Spokes
When you get your bike, the spokes have not been pre-stressed. Your wheels were built by automated machines and machines can sometimes make minor mistakes, check all your spokes are tight. If any are very loose carefully tighten them. First remove the free play (wobble) from the spoke, then carefully tighten to a similar tension as that of the looser spokes in your wheel. Note: If you over tighten what was a loose spoke it can often cause the wheel to buckle As your wheels bed in, you may find some of the spokes become loose. The best way to deal with a wheels bedding in, is to regularly put a 1/4 turn on each spoke after riding (especially the rear wheel). This will keep them tight & your wheels true (running straight). Once the spokes have passed their bedding in stage (stretching) you should not have to tighten spokes very often. If your wheel is buckled you can true the wheel by finding the bend in the rim & applying tension to the correct spokes to pull the rim back in line. This is a relatively skilled procedure & we recommend that you at least follow some of the tutorial videos on youtube: search ‘true bicycle wheel’